Installing GolfModz lights kits on your golf cart is a great way to enhance visibility, improve safety, and add a stylish touch to your ride. Whether you're a beginner or a DIY enthusiast, this guide will walk you through the installation process in simple, easy-to-follow steps.

Tools & Materials You’ll Need

Before starting, gather the following:

• GolfModz lights kit (headlights, taillights, wiring harness, switch, etc.)

• Basic hand tools (screwdrivers, wrenches, wire strippers, pliers)

• Electrical tape or heat shrink tubing

• Zip ties (for securing wires)

• Drill & drill bits (if mounting requires new holes)

• Voltage tester or multimeter (optional but helpful)

Step 1: Disconnect the Golf Cart Battery

Safety first! Before working on any electrical components:

1. Turn off the golf cart.

2. Locate the battery (usually under the seat or in a rear compartment).

3. Disconnect the negative (-) terminal first, then the positive (+) to prevent accidental shorts.

Step 2: Mount the Lights

Headlight Installation

1. Position the headlights – Most golf carts have pre-marked spots for lights. If not, choose a symmetrical location on the front cowl.

2. Mark drill holes – Use a pencil to mark where the mounting screws will go.

3. Drill pilot holes – Carefully drill holes to avoid cracking the plastic.

4. Secure the lights – Attach the headlights using the provided screws and brackets.

Taillight Installation

1. Locate mounting points – Taillights typically go on the rear fenders or body panel.

2. Drill if necessary – If no existing holes, mark and drill carefully.

3. Attach the lights – Secure them with screws and ensure they’re aligned properly.

Step 3: Run the Wiring Harness

1. Route wires neatly – Run the wiring harness from the front lights to the rear, tucking wires along the frame to avoid damage.

2. Use zip ties – Secure wires to prevent them from dangling or getting caught in moving parts.

3. Avoid sharp edges – Protect wires by running them through rubber grommets if passing through metal.

Step 4: Connect the Lights to the Wiring Harness

1. Match the connectors – GolfModz kits usually have plug-and-play connectors. Simply match colors (red to red, black to black, etc.).

2. Solder or crimp if needed – If no connectors, strip wires, twist together, and secure with solder and heat shrink or crimp connectors.

3. Test connections – Before finalizing, reconnect the battery briefly to check if lights turn on (then disconnect again to continue work).

Step 5: Install the Light Switch

1. Choose a switch location – Common spots are on the dashboard or under the seat.

2. Drill a hole for the switch – Ensure it fits snugly.

3. Wire the switch – Follow the kit’s instructions, typically:

   • Power wire (from battery or key switch) → Switch input

   • Switch output → Lights harness

   • Ground wire → Cart frame or battery negative

Step 6: Connect to Power Source

1. Identify a 12V or 48V source (depending on your cart’s voltage).

   • If unsure, use a multimeter to check voltage.

2. Tap into the battery or key switch – For a cleaner install, connect to the ignition so lights only work when the cart is on.

3. Use an inline fuse (if not included) to protect against electrical shorts.

Step 7: Reconnect the Battery & Test

1. Reattach the positive (+) terminal first, then the negative (-).

2. Turn on the golf cart and flip the light switch.

3. Verify:

   • Headlights and taillights illuminate.

   • No flickering or dimming (indicates a weak connection).

   • No blown fuses (if applicable).

Step 8: Secure & Finalize Installation

1. Tidy up wiring – Use zip ties to bundle loose wires.

2. Wrap exposed connections – Cover with electrical tape or heat shrink.

3. Double-check all mounts – Ensure lights are firmly attached and won’t vibrate loose.

Troubleshooting Common Issues

• Lights don’t turn on?

  • Check battery connections.

  • Verify switch wiring.

  • Test with a multimeter for power at the light connectors.

• Flickering lights?

  • Ensure all grounds are secure.

  • Check for loose or corroded wires.

• Blown fuse?

  • Replace with the correct amperage and inspect for shorts.

Conclusion

Installing GolfModz lights on your golf cart is a straightforward project that can be completed in 1-2 hours with basic tools. By following these steps carefully, even a beginner can achieve a professional-looking installation.

Now, enjoy your upgraded golf cart with improved visibility and style! If you run into any issues, consult GolfModz’s support or a local golf cart technician.

Happy cruising! 🚗💡